模压工艺参数对聚酰亚胺树脂压缩强度的影响及其数学模型的建立

doi:10.12066/j.issn.1007-2861.1823

Abstract

Abstract:

Influence of molding temperature and duration time on the strength of polyimide were investigated, and a mathematical model was established. The results indicate that the pressing parameters have significant effects on the strength of polyimide. The compressive strength reaches maximum when the molding temperature is 653 K and non-pressure duration time is 25 min. Besides, a fitted quadric multiple equation is obtained with orthogonal central composite design. It can fully characterize compressive strength of polyimide within the research domain.

Key words: polymers, molding, pressing, process parameters, temperature, duration time, mathematical model

CLC Number:

TQ322.3

FANG Lin, BURYA A I, YU Mingming, REN Musu, KALINICHENKO C B, EREMINA E A. Influence of molding process parameters on compressive strength for polyimide resin and establishment of mathematical model[J]. Journal of Shanghai University（Natural Science Edition）, 2018, 24(2): 272-277.

Add to citation manager EndNote|Reference Manager|ProCite|BibTeX|RefWorks

URL: https://www.journal.shu.edu.cn/EN/10.12066/j.issn.1007-2861.1823

https://www.journal.shu.edu.cn/EN/Y2018/V24/I2/272

Figures/Tables 6

Table 1

Table 2

Table 3

Table 4

Table 5

Fig.1

References 7

[1]	Le T H, Yang Y. Polyimide-based porous hollow carbon nanofibers for supercapacitorelectrode[J]. Journal of Applied Polymer Science, 2016, DOI: 10.1002/app.43397. doi: 10.1002/app.40385 pmid: 24976670
[2]	Freddy Y C, Boey X L. Modeling the curing kinetics for a modified bismaleimide resin[J]. Journal of Polymer Science Part A: Polymer Chemistry, 2000,38:907-913.
[3]	周洪飞. 聚酰亚胺树脂固化动力学参数研究[J]. 热固性树脂, 2005,20(4):11-13.
[4]	刘志真. RTM 聚酰亚胺复合材料力学性能研究[J]. 材料工程, 2007(1):98-101.
[5]	Ye X Y, Liu X H. Tribological properties of fluorinated graphene reinforced polyimide composite coatings under different lubricated conditions[J]. Composites Part A: Applied Science and Manufacturing, 2016,81:282-288.
[6]	陈建升, 左红军, 杨海霞, 等. 适用于 RTM 成型聚酰亚胺树脂的合成与性能研究[J]. 航空材料学报, 2006,26(3):183-186.
[7]	Xu X C, Yuan Z J. The molding study of polyimide polishing film[J]. Key Engineering Materials, 2008,375:288-292.

[1]	GAN Lu, YANG Jiong, XI Jinyang. Temperature-dependent band gap of thermoelectric PbTe from first-principles calculations [J]. Journal of Shanghai University（Natural Science Edition）, 2026, 32(1): 33-43.
[2]	HU Taishan, HU Shangmao, LIU Gang, MEI Qi, REN Xin, YAO Zheng. Enhancement efiect of carbon nanotube modifled phenolic resin composite carbon source on electrical properties of carbon ceramics [J]. Journal of Shanghai University（Natural Science Edition）, 2025, 31(5): 827-835.
[3]	YAN Zhichao, GUO Yanqun, WANG Dongxu, ZHOU Difan, CHEN Mingyue, ZHAO Suchuan, CAI Chuanbing. Spatial orientation of a magnetically coupled resonant wireless power transmission system based on YBCO superconducting coils [J]. Journal of Shanghai University（Natural Science Edition）, 2025, 31(5): 885-894.
[4]	LONG Xiumin, PAN Haojie, CAO Guixin. Mechanism and prospects of room-temperature magnetoresistance effect in (Fe_1-xNi_x)_5+δGeTe₂ single crystals [J]. Journal of Shanghai University（Natural Science Edition）, 2025, 31(4): 657-665.
[5]	HUANG Jizhong1, 2, 3 , ZHANG Hongfang1, 2, 3 , CHENG Yuan2, 3 , ZHENG Yi2 , HU Jinshuai1, 2, 3 , ZHANG Yue2, 3. Diffusion and condensation of water vapor in sandstone of varying weathering degrees in Yungang Grottoes [J]. Journal of Shanghai University（Natural Science Edition）, 2024, 30(6): 1018-1030.
[6]	YANG Yuanpeng, WU Chunlin. Steady-state thermal analysis of ellipsoidal inhomogeneities embedded in a bimaterial or semi-infinite domain [J]. Journal of Shanghai University（Natural Science Edition）, 2024, 30(5): 858-874.
[7]	ZHANG Boyang, WANG Hao, ZHOU Tao, WU Yongquan. Vacancy trapping during solidiﬁcation of Cu₅₀Ni₅₀ alloy [J]. Journal of Shanghai University（Natural Science Edition）, 2024, 30(2): 267-277.
[8]	YAO Xiaonan, ZHANG Mengxi, LIU Bing. Temperature effects of super-large concrete on the construction of a tunnel through a lake [J]. Journal of Shanghai University（Natural Science Edition）, 2024, 30(2): 308-317.
[9]	LU Baoming, XU Jinming. Estimation of environmental parameters of Yungang Grottoes based on empirical mode decomposition and long short-term memory artificial neural network [J]. Journal of Shanghai University（Natural Science Edition）, 2024, 30(1): 1-016.
[10]	WANG Xueqi, YU Jia, SHI Siqi. Preparation and interface improvement mechanism of MnO_x-doped PVA-based carbon-coated CF_x composite materials [J]. Journal of Shanghai University（Natural Science Edition）, 2023, 29(5): 973-990.
[11]	HE Luqiang, ZHOU Xiangyun, SUN Dean. Analytical study on temperature ﬁeld of high-level radioactive waste disposal repository [J]. Journal of Shanghai University（Natural Science Edition）, 2023, 29(4): 769-.
[12]	ZHENG Tianqing, XU Yanyi, ZHANG Yunhu, ZHAI Qijie. Distribution and evolution of the temperature field in a continuous casting billet heated by an electric current [J]. Journal of Shanghai University（Natural Science Edition）, 2022, 28(5): 857-871.
[13]	PENG Sisi, CAI Chuanbing, ZHENG Jun, GUO Shuqiang, XU Ying, ZHOU Difan. Application of YBCO high temperature superconducting tapes in superconducting energy storage devices [J]. Journal of Shanghai University（Natural Science Edition）, 2022, 28(5): 813-820.
[14]	DAI Peng, HAN Shulun, ZHOU Difan, GUO Yanqun, CAI Chuanbing. Frequency characteristics of magnetic coupling resonance superconducting wireless power transmission [J]. Journal of Shanghai University（Natural Science Edition）, 2022, 28(2): 324-332.
[15]	LIANG Lei, YU Mingming, WANG Peng. Preparation of high temperature resistant epoxy composites reinforced by carbon fiber [J]. Journal of Shanghai University（Natural Science Edition）, 2021, 27(5): 928-939.

Influence of molding process parameters on compressive strength for polyimide resin and establishment of mathematical model

RichHTML

PDF

Knowledge

Abstract

Cite this article

share this article

Figures/Tables 6

References 7

Related Articles 15

Recommended Articles

Metrics

Comments