基于FBG-3D打印的加强肋土工格栅拉拔试验

doi:10.12066/j.issn.1007-2861.2654

上海大学学报(自然科学版) ›› 2026, Vol. 32 ›› Issue (1): 116-129.doi: 10.12066/j.issn.1007-2861.2654

• 力学与土木工程 • 上一篇

基于FBG-3D打印的加强肋土工格栅拉拔试验

陈智富¹, 张孟喜¹, 戴治恒², 陈昌茂²

1. 上海大学力学与工程科学学院, 上海 200444;
2. 上海公路桥梁 (集团) 有限公司, 上海 200433

收稿日期:2024-12-12 发布日期:2026-03-16
通讯作者: 张孟喜(1963-),男,教授,博士生导师,博士,研究方向为新型土工加筋技术、隧道及地下结构等. E-mail:mxzhang@i.shu.edu.cn
基金资助:
上海市交通委员会2024年度科研课题资助项目(JT2024-KY-027)

Pull-out test of strengthening rib geogrid based on FBG and 3D printing

CHEN Zhifu¹, ZHANG Mengxi¹, DAI Zhiheng², CHEN Changmao²

1. School of Mechanics and Engineering Science, Shanghai University, Shanghai 200444, China;
2. Shanghai Road and Bridge (Group) Co. Ltd., Shanghai 200433, China

Received:2024-12-12 Published:2026-03-16

摘要/Abstract

摘要： 基于3D打印技术和光纤布拉格光栅(fiber Bragg grating,FBG)制备了一种加强肋中内嵌FBG压力传感区的加强肋土工格栅,通过试验验证了压力传感区在土中工作的可靠性.通过室内拉拔试验研究了加强肋格栅在不同加强肋高度、间距和数量下的拉拔界面特性,以及拉拔过程中加强肋侧压力的变化规律,基于刺入剪切破坏理论提出加强肋被动侧压力理论计算公式.结果表明,加强肋可以有效提高土工格栅的抗拉拔特性,土工格栅的极限拉拔力随着加强肋高度和数量的增加而增大,而加强肋间距过小会使极限拉拔力减小;加强肋被动侧压力先随拉拔位移的增加而逐渐增大,达到峰值后趋于稳定,加强肋主动侧压力则先下降后趋于稳定,纵肋上加强肋被动侧压力略小于网格上加强肋;在多加强肋情况下,拉拔方向后侧加强肋被动侧压力会减小,加强肋间距越小,被动侧压力减小幅度越大;加强肋被动侧压力理论计算结果与试验结果基本吻合.所得结果验证了将FBG传感器嵌入土工格栅加强肋监测侧压力的可行性,深化了加强肋土工格栅与填土间相互作用的机制理论.

关键词: 光纤布拉格光栅 (fiber Bragg grating, FBG), 3D打印, 加强肋土工格栅, 拉拔试验, 拉拔界面特性, 加强肋侧压力

Abstract: Based on 3D printing and fiber Bragg grating (FBG), a strengthening rib geogrid with FBG pressure sensing zones is prepared, and its reliability in soil is verified through experiments. Pull-out tests are conducted to study the pull-out interface characteristics of strengthening rib geogrids under different rib heights, spacings, and numbers, as well as the variation patterns of lateral pressure on the strengthening ribs. Based on the punching shear failure mechanism, the theoretical calculation formula for the passive lateral pressure of the strengthening ribs is established. The results show that strengthening ribs can effectively improve the pull-out resistance of geogrids. The ultimate pull-out force of the geogrid increases with the rib height and the number of ribs, while an excessively small rib spacing reduces the ultimate pull-out force. The passive lateral pressure of the ribs increases gradually with the pull-out displacement and stabilizes after reaching the peak value. The active lateral pressure decreases first and then stabilizes. The passive lateral pressure of the strengthening ribs located on the longitudinal ribs is slightly smaller than that on the mesh. In the case of multiple strengthening ribs, the passive lateral pressure of the strengthening ribs on the rear side in the pull-out direction decreases, and the smaller the rib spacing, the greater the degree of reduction. The theoretical calculation results of the passive lateral pressure of the strengthening ribs are in basic agreement with the experimental results. These results verify the feasibility of embedding FBG sensors into the strengthening ribs of geogrids to monitor lateral pressure and deepen the theoretical understanding of the interaction mechanism between strengthening rib geogrids and backfill.

Key words: flber Bragg grating (FBG), 3D printing, strengthening rib geogrid, pull-out test, pull-out interface characteristics, lateral pressure on strengthening ribs

中图分类号:

TU441

陈智富, 张孟喜, 戴治恒, 陈昌茂. 基于FBG-3D打印的加强肋土工格栅拉拔试验[J]. 上海大学学报(自然科学版), 2026, 32(1): 116-129.

CHEN Zhifu, ZHANG Mengxi, DAI Zhiheng, CHEN Changmao. Pull-out test of strengthening rib geogrid based on FBG and 3D printing[J]. Journal of Shanghai University（Natural Science Edition）, 2026, 32(1): 116-129.

参考文献

[1] 包承纲. 土工合成材料界面特性的研究和试验验证[J]. 岩石力学与工程学报, 2006(9): 1735-1744.
[2] 孟凡祥, 徐超. 筋土之间直剪试验与拉拔试验的对比分析[J]. 水文地质工程地质, 2009, 36(6): 80-84.
[3] 刘文白, 周健. 土工格栅与土界面作用特性试验研究[J]. 岩土力学, 2009, 30(4): 965-970.
[4] 杨广庆, 李广信, 张保俭. 土工格栅界面摩擦特性试验研究[J]. 岩土工程学报, 2006, 28(8): 948-952.
[5] Moraci N, Gioffe D `. A simple method to evaluate the pullout resistance of extruded geogrids embedded in a compacted granular soil [J]. Geotextiles and Geomembranes, 2006, 24(2): 116- 128.
[6] 王家全, 陆梦梁, 周岳富, 等. 土工格栅纵横肋的筋土承载特性分析[J]. 岩土工程学报, 2018, 40(1): 186-193.
[7] 张孟喜. 立体加筋土: 200510028241.8[P]. 2009-02-04.
[8] 蔡春, 张孟喜, 赵岗飞, 等. 带加强肋单向土工格栅的拉拔试验[J]. 岩土力学, 2012, 33(1): 53-59; 64.
[9] 李贵超, 张孟喜. 带加强锚固片的双向土工格栅拉拔试验研究[J]. 水力发电学报, 2017, 36(5): 104-111.
[10] 张孟喜, 马原, 邱成春. 加强节点布置方式对双向土工格栅拉拔特性的影响[J]. 上海交通大学学报, 2020, 54(12): 1307-1315.
[11] Mosallanezhad M, Taghavi S H S, Hataf N, et al. Experimental and numerical studies of the performance of the new reinforcement system under pull-out conditions [J]. Geotextiles and Geomembranes, 2016, 44(1): 70-80.
[12] 刘倩萁, 张孟喜, 洪成雨. 基于光纤传感技术的土工格栅变形及受力研究[J]. 水文地质工程地质, 2019, 46(6): 119-125.
[13] Hong C Y, Zhang Y F, Abro Z A. A fiber Bragg grating-based inclinometer fabricated using 3-D printing method for slope monitoring [J]. Geotechnical Testing Journal, 2020, 43(1): 20170277.
[14] Scott R, Vidakovic M, Chikermane S, et al. Encapsulation of fiber optic sensors in 3D printed packages for use in civil engineering applications: a preliminary study [J]. Sensors, 2019, 19(7): 1689.
[15] Hong C Y, Yuan Y, Yang Y Y, et al. A simple FBG pressure sensor fabricated using fused deposition modelling process [J]. Sensors and Actuators A: Physical, 2019, 285: 269-274.
[16] 李磊, 张孟喜, 周小凤, 等. 带加强节点双向土工格栅的拉拔试验研究[J]. 水利学报, 2012, 43(12): 1494-1499; 1506.
[17] 杜炜, 聂如松, 谭永长, 等. 格栅节点加强对风积沙筋土界面力学性能的影响[J]. 中南大学学报(自然科学版), 2024, 55(1): 172-187.
[18] Jewell R A, Milligan W E, Sarsby R W, et al. Interaction between soil and geogrids [C]// Proceeding of the Symposium on Polymer Grid Reinforcement in Civil Engineering. 1984: 19-29.
[19] Palmeira E M. Soil-geosynthetic interaction: modelling and analysis [J]. Geotextiles and Geomembranes, 2009, 27(5): 368-390.
[20] Peterson L M, Anderson L R. Pullout resistance of welded wire mats embedded in soil [D]. Logan: Utah State University, 1980.

基于FBG-3D打印的加强肋土工格栅拉拔试验

Pull-out test of strengthening rib geogrid based on FBG and 3D printing

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 4

编辑推荐

Metrics

本文评价

[1]	张志铭, 李茂, 胡庆夕, 张海光. 连续碳纤维复合材料曲面随形五轴3D打印工艺[J]. 上海大学学报(自然科学版), 2025, 31(5): 872-884.
[2]	陈逸伟, 李东, 庄欠伟, 张弛. 受泥浆浸泡影响的钢筋混凝土黏结特性试验研究[J]. 上海大学学报(自然科学版), 2025, 31(1): 143-156.
[3]	高俊丽, 徐宏飞, 袁川, 曹威. 不同温度环境下加肋土工膜与砂土界面拉拔试验的颗粒流数值模拟[J]. 上海大学学报(自然科学版), 2021, 27(2): 336-346.
[4]	邱成春张孟喜李秀玲. 条带式带倾齿加筋的界面特性及拉拔机理[J]. 上海大学学报(自然科学版), 2010, 16(6): 649-654.